Carrying on from my testing of the Fuji IS-Pro with various filters, next I tested the camera at night, comparing visible light only photography to full spectrum photography. By full spectrum, I mean the full spectrum that the IS-Pro can detect, i.e. light with a wavelength between 380nm and 1000nm. If you click the filenames of the two images below you can download RAWs to compare yourself.

Visible light only photo taken with the Fuji IS-Pro and B+W 486 UV IR Cut MRC filter (file has been converted to DNG and run through CornerFix to remove cyan vignetting caused by the filter)
_DIR0382_CF.dng Visible light only

Photo taken with the Fuji IS-Pro
_DIR0380.RAF Full spectrum

The above images were both shot at the same settings. The visible light only image has been run through CornerFix to remove cyan vignetting caused by the filter. The full spectrum image has had the white balance adjusted to the same colour temperature and tint as the visible light only image in ACR (they were shot in with auto white balance).

The full spectrum image is brighter overall. Looking inside the building, there doesn't appear to be much difference in brightness between the images. But the christmas trees above the doors are much brighter in the full spectrum image. The lights used on the Christmas trees must emit much more IR light than the lights used inside the building.

The full spectrum photo has a reddish cast, turning the sky slightly purplish. I don't find it particularly objectionable or 'unrealistic' though.

With regards to detail, the visible only image wins again. I would say there isn't as much difference between the full spectrum and visible only photos as there is during the daytime though. This is probably due to there being less IR light around at night.

Crop of visible light only photo taken with the Fuji IS-Pro and B+W 486 UV IR Cut MRC filter
Visible light only

Crop of full spectrum photo taken with the Fuji IS-Pro camera
Full spectrum

Crop of full spectrum photo taken with the Fuji IS-Pro camera and CA corrected in ACR
Full spectrum with CA corrected

I also tried using CA correction on the full spectrum photo, I would say it is a very minor improvement. Definitely still behind the visible only photo.

The below two images were shot with tungsten white balance:

Visible light only photo taken with the Fuji IS-Pro and B+W 486 UV IR Cut MRC filter
Visible light only

Full spectrum photo taken with the Fuji IS-Pro camera
Full spectrum

As you can see, the full spectrum photo has a much more neutral white balance of the church, a bit too neutral really. The sky is slightly purple, and the purple bush further back in the photo gives away that the photo contains IR. The visible light only photo is darker again, and the church has a very yellow tone despite the tungsten white balance setting.

Adjusting the white balance to try and get the correct colour of the church (yellow sandstone or ironstone), I ended up with the below:

Visible light only photo taken with the Fuji IS-Pro and B+W 486 UV IR Cut MRC filter, white balance adjusted in ACR
Visible light only with wb adjusted

Full spectrum photo taken with the Fuji IS-Pro camera, white balance adjusted using curves in PS CS5
Full spectrum with wb adjusted

For the visible light only photo, I think the Church looks quite good, but the sky is far too blue. For the full spectrum photo I tried using both the white balance adjustment in ACR and curves in Photoshop, though found it hard to get the colour of the church quite right without toning everything yellow too much.

Again, for these photos the visible light only photo contains more detail than the full spectrum photo.

Here's some photos of a shopping street with cars moving past:

Full spectrum photo taken with the Fuji IS-Pro camera
Full spectrum

Visible light only photo taken with the Fuji IS-Pro and B+W 486 UV IR Cut MRC filter
Visible light only

Infrared photo taken with the Fuji IS-Pro and Hitech 85 Infrared filter
Infrared

The full spectrum photo seems to have a more neutral colour balance again, with the shops not having such a yellow cast from the lights. Lens flare isn't very good on any of these shots, but the Infrared only shot is particularly bad.

To compare lens flare, I went out again another night, and did another test shot:

Full spectrum photo taken with the Fuji IS-Pro camera
Full spectrum

Visible light and infrared photo taken with the Fuji IS-Pro and B+W UV 010 MRC filter
Visible light and infrared

Visible light only photo taken with the Fuji IS-Pro and B+W 486 UV IR Cut MRC filter
Visible light only

Visible light only photo taken with the Nikon D200 camera
Nikon D200 (Visible light)

These were taken still using the same Nikon 18-70mm/3.5-4.5 lens used for all the other photos, and with the lens hood attached. The full spectrum photo on the IS-Pro displays quite a bit of lens flare. Adding a UV filter only worsens it. And replacing the UV-cut filter with the UV-IR cut filter makes it even worse, with a big chunk of red lens flare appearing.

The D200 image meanwhile, taken with the same lens and no filters, doesn't display too much lens flare. There is a large arc lens flare on the left hand edge of the image, but I don't find this very objectionable. There are also smaller circles of lens flare to the left of the lamps. These are more objectionable, but still a lot better than the Fuji.

The photos for this lens flare test should not be compared in terms of exposure - they were taken with different shutter speeds and adjusted for exposure in ACR.

So, I don't think I will be using the Fuji IS-Pro for night photography, mainly due to the lens flare issues.

Leave a Reply

Your email address will not be published. Required fields are marked *